Open Address Management from your signed-in account security area and confirm whether the withdrawal whitelist restriction is enabled. Take the asset, network, full address and any required MEMO or Tag from the destination’s current deposit page, then add the address and complete every verification shown. Do not withdraw until both the whitelist setting and the saved address have a clear usable status.
What does a withdrawal whitelist actually control?
A withdrawal address whitelist limits the external destinations your account can send crypto to. Address Management stores the address, label and approval state; the restriction only becomes meaningful when the whitelist setting is enabled and the destination has passed the checks required on your current account. Naming an address does not verify it, and an approved address does not prove that you selected the right network.
| Feature | What it controls | Common mix-up |
|---|---|---|
| Withdrawal address whitelist | Which external addresses may receive withdrawals | It is not one universal contact for every asset and network |
| Address Management | Saved addresses, labels and verification state | A saved entry may not yet be available for withdrawal |
| API IP whitelist | Which network sources may use an API key | It does not approve a blockchain destination |
| Email allowlist | Whether messages are filtered by your email provider | It does not restrict where funds can go |
If you are still deciding which chain to use, start with the deposit and withdrawal network guide. A whitelist can restrict the destination, but it cannot make an unsupported network compatible.
Prepare these four things before adding an address
- The destination’s current asset and network: read both from the receiving exchange’s deposit page or from the wallet network you control. Do not copy them from an old message.
- The complete address and any extra identifier: copy the full address. If the destination also provides a MEMO, Tag or Payment ID, keep that field with the same transfer instructions.
- A secure verification route: make sure your linked email, authenticator or passkey is under your control and has no unfamiliar forwarding rule or device.
- A workable first-transfer check: confirm that the destination minimum, current withdrawal fee and deposit conditions allow a small transfer that will actually be credited.
Use a label you will still understand later, such as “My hardware wallet — BTC network” or “Exchange account — USDT — Tron.” Never place a private key, seed phrase, password or one-time code in the label. If somebody else owns the address, ask them to retrieve it from their current receiving page and confirm it through a separate contact route you already trust.
Step 1: open Address Management and check the whitelist setting
Sign in through an official route you saved yourself, then look in the account security area for Withdrawal Whitelist, Address Management or an equivalent label. Binance Academy’s account-security guide describes Account → Security → Withdrawal Whitelist, with Address Management as another entry point. Names and positions can differ by app version, device and region, so use the wording on your current screen rather than forcing an old tutorial to match.
Before adding anything, check the main whitelist switch, the existing address list and the state displayed beside each entry. If the restriction is off, read the consequences and the security checks shown before enabling it. The address list by itself is not proof that withdrawals are limited to approved destinations; the account must explicitly show that the relevant restriction is active.
Stop if you find an address, confirmation email or recent security change you do not recognize. Secure the linked email and review account devices before creating another destination or attempting a withdrawal.
Step 2: match every address field to the receiving page
Choose Add Address and fill in the asset, network, withdrawal address and label shown by your interface. Start from the receiving side: select the deposit network there, then choose exactly the same network on Binance. A familiar ticker does not prove that two contracts are the same, and an identical-looking EVM address does not prove that the receiving service supports the chain you selected.
After pasting, compare the complete address—not only the first and last characters. A MEMO or Tag is not a personal label. If the destination displays one, enter it in the dedicated field; if it does not, do not invent one from a different transfer guide. The MEMO and Tag guide explains why custodial platforms sometimes need both fields.
Step 3: complete the verification shown for this address
Submitting the form can trigger email confirmation, another account security check or an address-ownership check. Binance Academy’s account-security guidance says a new address requires email confirmation when Address Management is enabled. That makes the linked email part of this control: give it a unique password and a separate second factor, and review its forwarding rules. Nobody who claims to be support should ask for your live code or remote control of your screen.
Some withdrawals affected by Travel Rule checks may show a Satoshi Test or another ownership-verification flow. Binance Academy’s Satoshi Test explanation describes a prompted process in which a specified small test transfer is sent to the destination, and the recipient confirms the actual amount and transaction ID before the address is stored in Address Management. This is not a universal step for every withdrawal and it is not a number to guess. Follow it only when your signed-in page requires it.
Step 4: confirm the address is usable before the first withdrawal
An address appearing in the list proves only that an entry was saved.
Check that the page identifies it as verified or otherwise approved, that the whitelist restriction is active, and that the entry applies to the asset and network you intend to use. If the page still shows a hold, pending check or security notice, do not use repeated withdrawal submissions as a status test.
At the withdrawal preview, check the amount, fee, expected receipt and the destination’s minimum deposit again. When both services allow it, begin with an amount large enough to be recognized but small enough to limit the consequence of a mistake. After it arrives, reopen both pages and compare the address, network and current status before sending more. One successful transfer proves only that the previous transfer worked under the conditions at that time.
What errors can a whitelist not prevent?
- The wrong address was approved
- The control restricts withdrawals to saved destinations; it cannot know who you intended to pay. Review the full address before approval and again before withdrawal.
- The wrong asset or network was selected
- Address formats can overlap across networks. Approval does not prove that the receiving platform supports the chain actually used.
- The linked email is compromised
- If someone can read confirmation messages or control recovery, the protection is weakened. Email security is part of the whitelist setup.
- The destination changed its deposit requirements
- Only the destination’s current page can confirm whether an old address, contract, MEMO or minimum deposit remains valid.
- You approve an address supplied by a scammer
- Impersonated support and “safe wallet” scams try to make the account owner complete the approval. The whitelist cannot judge the person giving you instructions.
Use the whitelist as one layer alongside the account security checklist, not as a replacement for email protection, strong authentication, device review and a final transfer check.
The address was added but withdrawal still fails
| What you see | Check first | Avoid |
|---|---|---|
| The address cannot be saved | Asset, network, address format, extra identifier and the exact error | Pasting it into an unfamiliar “address checker” |
| Saved but unavailable to select | Verification state, whitelist switch, pending notice, asset and network | Deleting and recreating it repeatedly |
| Selectable but withdrawal is rejected | Available balance, minimum amount, security restriction and network status | Submitting the same request over and over |
| A TxID exists but funds are not credited | On-chain state, actual network, destination and deposit requirements | Giving a seed phrase to somebody offering to “speed it up” |
The first two cases belong in Address Management and account security. Once a withdrawal request exists, use the withdrawal status and TxID guide to separate a platform-stage problem from an on-chain one. Keep the complete error text, time, device and checks already performed. Official support does not need your password, authenticator code, recovery phrase or a full portfolio screenshot.
How should you review saved addresses?
Review by actual use, not by recreating everything on a schedule. Confirm that each label still identifies a destination you recognize, the asset and network are not mixed up, and you still control the receiving wallet or account. Removing an entry is also a security change, so first confirm that you no longer need it for a planned transfer and retain only the non-sensitive records you need.
If a new address or confirmation message was not yours, pause withdrawals, protect the linked email from a trusted device, remove unfamiliar sessions and review API and security settings. Do not transfer the remaining balance to a “safe address” supplied by somebody contacting you. Tallypier cannot view, add or remove entries in your Binance account and will never ask you to send an account screenshot or verification code.